![]() STEP 22: You can ow click on Start and Login to your macOS machine. STEP 21: Go to Settings on VirtualBox, then go to Storage, Right Click on macOS Big Sur 11.0 ISO File and remove attachment as shown below. Shutdown your macOS machine and then Open VirtualBox Settings. STEP 20: Setup Completed but we have to remove the installation ISO before we start using else it’ll boot into the Installation Page whenever we try to access it. STEP 19: Also set a Username and Password for your machine and then choose between Light Mode and Dark mode Theme and Continue. Set your Country, Region, Privacy settings and continue. STEP 18: After about an hour of restarting over and over again it should be successfully installed and we can now setup based on our preference. ![]() You just have to wait patiently and allow it install. Note: It may take an hour or more to install and It’ll restart severally while installing. STEP 17: Select the drive we just erased and then Continue and it should start Installing. STEP 16: After Erasing the partition or drive, Close the Window and Click on Install macOS and then Continue. You can give it whatever name when erasing. STEP 15: Now select the Disk we allocated earlier and Erase ( VBOX HARDDISK Media). STEP 14: Set a Language for the Installation and Continue. Open VirtualBox and Click on Start to Start the Installation. STEP 13: Now we can begin the installation. Line by line until you finish (you shouldn’t get any error).Ĭlose Command Prompt after entering all the commands. STEP 12: Paste each command in command prompt and hit enter. And then run Command Prompt on your PC as Administrator. STEP 11: Change “VM Name” in the commands to your macOS machine name we copied earlier. VBoxManage modifyvm "VM Name" -cpu-profile "Intel Core i7-6700K" VBoxManage setextradata "VM Name" "VBoxInternal/Devices/smc/0/Config/GetKeyFromRealSMC" 1Ĭopy the additional command only if you are using an AMD based CPU. VBoxManage setextradata "VM Name" "VBoxInternal/Devices/smc/0/Config/DeviceKey" "ourhardworkbythesewordsguardedpleasedontsteal(c)AppleComputerInc" ![]() VBoxManage setextradata "VM Name" "VBoxInternal/Devices/efi/0/Config/DmiBoardProduct" "Mac-AA95B1DDAB278B95" VBoxManage setextradata "VM Name" "VBoxInternal/Devices/efi/0/Config/DmiSystemVersion" "1.0" VBoxManage setextradata "VM Name" "VBoxInternal/Devices/efi/0/Config/DmiSystemProduct" "iMac19,1" You can also download the commands HERE cd "C:\Program Files\Oracle\VirtualBox\" CommandsĮnter the commands one at a time, line by line. We have to switch up VirtualBox settings for our Mac OS Virtual Machine so it recognises our PC as a Mac and installs without any issue.Ĭopy the commands below into Notepad on your PC. STEP 10: One last thing before we install Then increase the Video Memory to 128MB and enable 3D Acceleration as shown below and then click Ok to apply changes. You can change the Base Memory and Processor Cores whenever you want to make your Machine perform better. Copy your machine name from General Tab (we will make use of it later). STEP 7: After creating a new Virtual Machine, we have to make few changes to it.Ĭlick on Settings. Then Click on Finish to Apply the Changes we’ve made. STEP 6: Select Create a Virtual Hard Disk Now and set a disk size for your macOS machine. Note: You shouldn’t allocate more than 40% of your PC resources to your Virtual Machine else it’ll slow down your main PC. STEP 5: Set the Base Memory (which is your RAM) to whatever you want to allocate to this machine and then Set the Processor Cores as well then Next. Set the Type to Mac OS X and Version to Mac OS X (64 bit) and then next. Set the Machine to macOS Big Sur or whatever you want, leave the folder option as it is, Select the ISO Image and Specify the Big Sur image file we downloaded earlier from the requirements section. STEP 4: Click on New to create a new Virtual Machine STEP 3: After installing the Extension Pack, Click on the Tab icon as shown below and head back to the welcome page. STEP 2: Install VirtualBox after downloading by double clicking on it and following the prompt.Īfter installing VirtualBox we have to add the extension pack we downloaded to VirtualBox.ĭouble Click on VirtualBox Extension Pack in your download folder and it should load up in VirtualBox, Agree to the terms and Install. Also Click on All Supported Platforms under the VirtualBox Extension pack to download.ĭownload macOS Big Sur ISO Image File as well.Īnd you should have your downloaded files ready STEP 1: Download VirtualBoxand VirtualBox Extension Pack.Ĭlick on Windows Host and it should start Downloading.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |